Implus:
Description: Implus is another
of the cattle implants that bodybuilders are utilizing in the
attempt to get steroids. This product comes in a rotary cartridge
that contains 20 pellets per cartridge with 5 cartridges in a
box. Each pellet is 3" in length and contains 200 mgs. of
testosterone propionate as well as 20 mgs. of estradiol benzoate.
The estradiol is added to the product to increase size in cattle.
Implus is a drug intended for veterinarian use in cattle to increase
weight gain and feed efficiency. This product is identical to
Syno-H except that there are twice the amount of pellets in one
cartridge and the black market price is marketly less expensive
on this product. This is probable due to the fact that most people
are only aware of Finaplix and Syno'
as a rule. The unfortunate
side to using this for athletic gains is that it contains estradiol
which will cause big time gyno if it is left in the product and
used as is. You can read further about the effects of testosterone
propionate on it's page. I don't want to be redundant here. As
far as side effects go, if you don't seperate the estradiol from
the pellets you are going to be screwed with gyno, you don't want
to have. These are not the most sanitary things either. Keep in
mind that these were made for animals and there is not near the
precautions taken when making these as there is with medicine.
The other side effects are the same as with testosterone propionate.
There is a way to remove the estradiol from the implant by doing
to following: Gather about 2-3 of the pellets together and grind
them up with the back of a spoon and make the pellets into as
fine of a powder as you can. Then, get 50 ml of diethyl ether
(pretty easy to obtain from any chemical supplier) and mix this
combination together in a bowl. You then have to let the solution
evaporate allowing crystals to form in the bowl. The crystals
that form at the top of the bowl contain the estradiol that you
are trying to get rid of. You then need to place this solution
in the freezer overnight to help aid in most of the estradiol
being removed from the testosterone-ether solution. By the next
morning, you will pull this solution out of the freezer and the
frozen crystallized estradiol will have risen to the top of the
bowl (just like bread rising in the oven, he! he!). You then would
scrape or scoop the crystals off the top of the solution and get
rid of them. The remaining crystal that are left at the bottom
of the bowl contain the testosterone propionate that you are trying
to get. Then let them air dry for a while to get the majority
of the ether off the crystals. You then need to place these crystals
in the oven on a low temperature to get rid of any ether that
remains for a few hours and you should have left the dry testosterone
propionate crystals that you need with a minimum of ether left
in them. Make sure you have let them air dry first though. You
don't want to blow up the house by putting a bowl of ether in
the oven just because you are a little to fucking impatient to
get big. Make sure that it is a electric oven as well, you definitely
don't want to use a gas oven for this procedure. After separating
the testosterone propionate from the solution, you have two choices
for using this compound. One way is to use DMSO (dimethyl sulfoxide)
to make the steroid transdermal meaning that it will now pass
through the skin. There are a variety of forms that DMSO is available
but the gel version works the best and is the easiest to use.
What you want to do is grind up the crystals to as fine of a powder
as you can and then mix it with one teaspoonful of DMSO and one
of water and apply to the skin every 2-3 days as that is the effective
time span for testosterone propionate. You can then rub this compound
into your skin and wrap the area with a piece of saran wrap to
help get the compound to absorb into the skin easier, since it
will heat it between the saran wrap and your body to aid in absorption.
The other way to take this compound is through injection. You
can do this by mixing the compound with about 2 cc of oil or sterile
water and injecting it that way. Even grinding up the particles
as fine as you can you will have to use about an 18 gauge needle
to inject this concoction. I would suggest using the DMSO method
above to do this.
Effective Dose: 50 - 100 mgs. every other day.
Street Price: The going street price on this product is about
$70 per cartridge which will yield about 4000 mgs. of testosterone
propionate.
Stacking Info: This compound is commonly stacked with Winstrol
Depot, Metandiabol or Reforvit-B, or Parabolan
|
